
foundation Hacking Services
Wall Hacking Services in Singapore
Non-structural wall removal handled cleanly, with permit applications managed on your behalf.
What wall hacking involves
Wall hacking is the controlled removal of a wall, or part of one, to change the layout of a space. In a Singapore flat or apartment that usually means taking out a partition between two rooms, forming an opening to connect spaces, or removing a wall entirely to open up a floor plan.
The work itself is straightforward. What determines whether it can happen at all is the wall: non-structural walls can generally be removed with approval, while reinforced concrete walls cannot be touched under any circumstances.
Which walls can come out
Only non-structural walls are candidates. These are partitions that divide space without carrying load from the floors above. Reinforced concrete walls, beams, columns and the household shelter are all permanently off limits, and no permit covers them.
The flat's structural plan is what settles the question. It marks reinforced concrete explicitly, and it should be read before any quotation is given. Tapping a wall to listen for a hollow sound is widely repeated advice and is not reliable enough to act on.
If the wall you want removed turns out to be structural, the layout needs to change. That is a better outcome than discovering it partway through the work.
Approval comes first
Hacking a wall in an HDB flat requires a renovation permit issued before works begin. The application must be submitted by an HDB Registered Renovation Contractor, not by the flat owner directly.
Where the proposed opening is near a structural element, HDB may require the application to carry a Professional Engineer endorsement. This is established at application stage and affects the timeline, so it is worth identifying early.
In a private condominium the approval comes from the MCST instead, and requirements vary between developments. Most require an application, a deposit, contractor insurance details and an agreed work schedule.
Forming an opening rather than full removal
Partial hacking to create a doorway or a pass-through is common and is often the right answer where full removal is not possible or not wanted. It still needs a permit, and the application has to show the opening dimensions along with any lintel required above it.
An opening is not automatically simpler than removing the whole wall. The lintel detail and the making good around the new reveal can make it the more involved job of the two.
What the work includes
- Reviewing the structural plan and confirming what may be removed
- Preparing and submitting the renovation permit application
- Screening the work area and protecting floors, doorways and common corridors
- Isolating any electrical or plumbing services running in the wall
- Cutting and removing the wall or forming the opening
- Making good where the wall met the floor, ceiling and adjoining walls
- Sorting, removing and disposing of debris at licensed facilities
Services inside the wall
Walls frequently carry electrical conduit, switch drops and occasionally water pipes. These have to be traced and isolated before hacking starts, and re-routed afterwards where the circuit is still needed.
This is worth raising before work begins rather than discovering it on the day, because a wall that turns out to carry a live circuit changes the sequence and may need a licensed electrician involved.
Making good
Removing a wall always leaves marks where it met the floor, the ceiling and the walls on either side. Some patching and levelling is unavoidable. Clarify whether making good is included in the scope or whether the surfaces are being handed over for your renovation contractor to finish, because assumptions on this point cause more disputes than the hacking itself.
Working hours and duration
Noisy work including hacking is restricted to weekdays, generally 9am to 5pm, and is not permitted on Saturdays, Sundays or public holidays. HDB also limits demolition and finish removal to three consecutive days, and restricts how many powered hand tools may run at once.
This constrains how quickly a job can be done regardless of how many people are on site. Any programme that involves hacking over a weekend is describing something that is not permitted.
Wall hacking prices at a glance
Published market ranges for wall hacking in Singapore, as a guide before you request a quote. These are not our prices; a site survey gives the firm figure.
| Job | Typical market range |
|---|---|
| Single non-structural wall, HDB flat | S$1,500 to S$3,000 |
| Multiple walls, or condo and landed | S$5,000 to S$10,000 |
| Rate per square metre of wall | S$100 to S$250 per m² |
For the full breakdown by property type and job, read the wall hacking cost guide. For floors, toilets, kitchens and disposal, see the hacking price list.
For typical market prices across walls, floors, toilets, kitchens, ceilings and disposal, see our hacking price list.